MUSIC ROOM SOUNDPROOFING MASS LOADED VINYL BARRIER


MLV loaded vinyl barrier: Is a specialty developed acoustic layer product offering superior noise reduction soundproofing. Vinyl damper sheet offers STC Ratings up to 32, It is a low cost material used for a variety of Home Theater and land based room Residential/industrial/commercial Studio sound barrier soundproofing. This typical application would improve transmission loss between Residential, office adjoining room spaces. The combination of the damping and stiffness properties of MLV sound proofing gives it excellent performance as a combined layer and damper when applied to partition panels and lightweight structural bulkheads, reducing room transmission of both airborne and structure Borne noise attenuation. Application direct to panels is best done with pre-applied pressure sensitive adhesive (PSA) backed up minimal fasteners or staples. Ideal product for sound studio, garage, basement and recording studio and much more.

Rockwool is made of slag, which is a recycled steel product, and rock, a trap rock mined in Texas...those are the only raw materials in rockwool insulation.mass loaded vinyl barrier we use "coke" which is a recycled material from coal. it is used to make the heat hotter in the manufacturing process, in order to save energy...rockwool is the safest insulation on the market today...it also has one of the best thermal insulating properties as well as a superior sound control while not supporting mold or mildew. all while not having to add any chemicals...many other insulation products on the market today are either all chemical, foams, or have chemicals added to them to keep them fire retardant, cellulose...

Wholesale MLV Barrier and other noise reduction, sound barrier, soundproofing materials.
E.2.3 Coefficient of absorption. All materials absorb some sound, and the percentage of sound is measured (in laboratory tests) as a coefficient of absorption. Coefficients of absorption range in value from close to 0 (no absorption) to nearly 1.0 (100 % efficient); these coefficients vary as a function of frequency. Materials that are most efficient at absorbing sound include soft porous "fuzzy» materials such as glass fiber, mineral wool fiber, carpet, curtains, acoustic tile, and other specialty materials. Materials that depend on their porosity to absorb sound should not be painted which will clog their pores, and thus degrade their acoustical performance.

Mass loaded vinyl UL 94 HB Pass FMVSS 302 Self Extinguishing Tolerances are 0 +/- 1/8" for width.

Stone wool insulation AFB

is a light-weight, semi-rigid batt that provides fire resistance and sound control.

Applications:
This product is designed for commercial, industrial, and residential buildings as a fire stopping. Ideal for filling:

  • Perimeter insulation gaps between concrete floor slabs and exterior wall systems
  • Around conduit pipe and duct openings through walls and floor slabs
  • Between fire walls and ceiling slab insulation
  • Be safe N' Sound

Roxul SAFE®

is used in conjunction with a fire sealant to prevent passage of fire and smoke.

Properties:

  • Non-combustible with melting point of approx. 1177°C (2150°F)
  • Does not promote smoke or flame spread when exposed to flame
  • Minimal shrinkage to maintain critical line of defense against fire
  • Low thermal conductivity
  • Water and moisture resistant; does not absorb moisture to maintain insulating value
  • Does not rot, promote mildew, fungi, or bacteria, or sustain vermin
  • Can be faced with reinforced foil facings
  • Earns LEED® points – talk to Roxul’s LEED® Accredited Professional

  • Recommendations when using: face mask & glasses.

     

Technical Data:

Compliance and Performance:
CAN4 - S115M Standard Test Method of Firestop Systems Complies
ASTM C 612 Stone Fiber Block and Board Thermal Insulation Type IVA, Complies
MEA Approval New York City Approval 339-97-M
City Of Los Angeles Approval RR 25444
ULC Design Nos. Consult UL Directory for numerous approved fire-rated joint
systems, through penetration designs and curtain wall design
listings, or contact Roxul for further more information
Fire Performance:
CAN4 S114 Test for Non-Combustibility Non-Combustible
ASTM E 136 Behavior of Materials at 750°C (1382°F) Non-Combustible
CAN/ULC S102 Surface Burning Characteristics Flame Spread = 0
Smoke Developed = 0
ASTM E84 (UL 723) Surface Burning Characteristics Flame Spread = 0
Smoke Developed = 0
     
Smolder Resistance:
CAN/ULC S129 Smolder Resistance 0.01%
Moisture Resistance:
ASTM C 1104 Moisture Sorption 0.04%
Corrosive Resistance:
ASTM C 665 Corrosiveness to Steel Pass
ASTM C 795 **** Stainless Steel Stress Corrosion Specification
as per Test Methods C871 and C692: U.S. Nuclear Regulatory Commission, Reg. Guide #1.36: U.S. Military Specifications MIL-I-24244 (all versions including B and C)		  Conforms
Weight 2.8 lbs cu/ft  
Interior Walls with Steel Studs:
Stone wool insulation installed between steel 2 x 4 studs on 24" centers and 5/8" drywall (type x) provides:
  • Fire Rating: 1 hour
  • Sound Transmission Class (STC): 52

 
Acoustical Performance::
ASTM C423
CO-EFFICIENT AT FREQUENCIES
Thickness 125 Hz 250 Hz 500 Hz 1000 Hz 2000 Hz 4000 Hz NRC
2.0" 0.26 0.68 1.12 1.10 1.03 1.04 1.00
3.0” 0.63 0.95 1.14 1.01 1.03 1.04 1.05
4.0” 1.03 1.07 1.12 1.04 1.07 1.08 1.10

Call us for shipping costs.

 

 

Click here to order

5 items found
Sort By: